Supported Devices
IMD-02
- PDUs with Geist Interchangeable Monitoring Device (IMD), variant IMD-02
- 5W5H6A9HXX-S
- 6HW56A9BXX-S-030160
- 8HW56A9BXX-S-030160
IMD-03
- PDUs with Geist Interchangeable Monitoring Device (IMD), variant IMD-03
Required WNC Firmware
IMD-02
- 36.02 or newer
- 36.10 or newer for per-outlet readings (if supported by PDU)
IMD-03
Geist Documentation
The following resources will be useful for the WNC configuration. Note, this is not a full guide to the interface on Geist PDUs.
Required PDU Configuration
The device must be reset to factory defaults before connecting the WNC . Insert a paper clip or other tool into the network-reset button (3 in the images below).
| IMD-02 devices | IMD-03 devices |
 |  |
| Hold the network reset button (3 in the image above) for 15 seconds to restore the default IP address. | Hold the network reset button (3 in the image above) until the display shows "rESt" to restore the defaults. |
WNC Connections
1. Connect one end of an ethernet cable to the ethernet port #1 on the PDU control panel
| IMD-02 devices | IMD-03 devices |
 |  |
2. On the rear of the WNC, connect the other end of the ethernet cable and the 5V DC power supply barrel plug.
3. Optional: The WNC can instead be powered from the Geist PDU directly (certain models only). Contact sales@packetpower.com to discuss the necessary cabling.
Readings Reported
Not all readings are available for all Geist IMD-2/IMD-3 PDUs. For example, a single phase PDU will not report any readings for input phases B or C. Additionally, per-outlet readings are only available on a PDU that supports per-outlet readings.
| SNMP OID | Channel | Description |
| 1.3.6.1.4.1.21239.5.2.3.2.1.4.1 | Voltage A | PDU phase A voltage |
| 1.3.6.1.4.1.21239.5.2.3.2.1.4.2 | Voltage B | PDU phase B voltage |
| 1.3.6.1.4.1.21239.5.2.3.2.1.4.3 | Voltage C | PDU phase C voltage |
| 1.3.6.1.4.1.21239.5.2.3.2.1.8.1 | Current A | PDU phase A current |
| 1.3.6.1.4.1.21239.5.2.3.2.1.8.2 | Current B | PDU phase B current |
| 1.3.6.1.4.1.21239.5.2.3.2.1.8.3 | Current C | PDU phase C current |
| 1.3.6.1.4.1.21239.5.2.3.2.1.12.1 | Power A | PDU phase A power |
| 1.3.6.1.4.1.21239.5.2.3.2.1.12.2 | Power B | PDU phase B power |
| 1.3.6.1.4.1.21239.5.2.3.2.1.12.3 | Power C | PDU phase C power |
| 1.3.6.1.4.1.21239.5.2.3.2.1.15.1 | Energy A | PDU phase A energy |
| 1.3.6.1.4.1.21239.5.2.3.2.1.15.2 | Energy B | PDU phase B energy |
| 1.3.6.1.4.1.21239.5.2.3.2.1.15.3 | Energy C | PDU phase C energy |
| 1.3.6.1.4.1.21239.5.2.3.2.1.14.1 | Phase Angle A | PDU phase A angle |
| 1.3.6.1.4.1.21239.5.2.3.2.1.14.2 | Phase Angle B | PDU phase B angle |
| 1.3.6.1.4.1.21239.5.2.3.2.1.14.3 | Phase Angle C | PDU phase C angle |
| 1.3.6.1.4.1.21239.5.2.3.1.1.9.1 | Total Power | PDU total power |
| 1.3.6.1.4.1.21239.5.2.3.1.1.12.1 | Total Energy | PDU total energy |
| 1.3.6.1.4.1.21239.5.2.3.6.1.8.X | Current X | PDU outlet X current |
| 1.3.6.1.4.1.21239.5.2.3.6.1.12.X | Power X | PDU outlet X power |
Uploading ....